| Author |
Message |
stefuel
Joined: 07 Mar 2006
Posts: 3353
Location: Green Harbor MA USA
|
| Posted: Sun Jun 01, 2008 11:32 pm Post subject: Curt, calling Curt. |
|
|
You got PM about Upton MA.
_________________
Chip
A Barco is only a AmPro with training wheels
Card carrying member of the AVS chain gang.
|
|
| Back to top |
|
 |
grogthegreat
Joined: 16 May 2007
Posts: 166
Location: San Diego, CA
|
| Posted: Mon Jun 02, 2008 2:42 am Post subject: |
|
|
Thats close to me. Whats going on?
Come on, you can tell me!
-Grog
_________________
First projector: Sony 1252q with 3500 hours
Second projector: NEC 9PG+
current projector: Sony G90
100" 3:4 draper screen.
I must keep upgrading till the voices stop!!
"I CAN HAZ CRT PRUJEKTER."
-Curt Palme
|
|
| Back to top |
|
|
Curt Palme
CRT Tech
Joined: 08 Mar 2006
Posts: 24396
Location: Langley, BC
TV/Projector: All of them!
|
| Posted: Mon Jun 02, 2008 3:15 am Post subject: |
|
|
THe customer posted on avs, I just sold him a G90, it's DOA. No standby light, nuffin'.
Customer doesn't know how to use a meter, so he can't do much other than changing the fuses (which didn't help.).
I am sending him spare parts tomorrow, but someone local that can use a meter would be handy..
|
|
| Back to top |
|
|
stefuel
Joined: 07 Mar 2006
Posts: 3353
Location: Green Harbor MA USA
|
| Posted: Mon Jun 02, 2008 10:40 am Post subject: |
|
|
He's got a appointment to have it calibrated this coming Sat I think. I warned him in the other thread about setting up a cal date without testing it on site first. The absolute quickest I could get there "might" be Wed after work. If he is desperate, he can run it down to me any night this week and I'll look at it while he waits. I have a screen and RGBHV outlet in the garage so we could just plug it in and let-er-rip. I've never worked on a G-90 but I'm sure with Curt on the other end of a phone we could diagnose it in short order.
_________________
Chip
A Barco is only a AmPro with training wheels
Card carrying member of the AVS chain gang.
|
|
| Back to top |
|
|
Heywood Jablome
Joined: 12 Mar 2006
Posts: 1548
|
| Posted: Mon Jun 02, 2008 11:17 am Post subject: |
|
|
| stefuel wrote: | | He's got a appointment to have it calibrated this coming Sat I think. I warned him in the other thread about setting up a cal date without testing it on site first. The absolute quickest I could get there "might" be Wed after work. If he is desperate, he can run it down to me any night this week and I'll look at it while he waits. I have a screen and RGBHV outlet in the garage so we could just plug it in and let-er-rip. I've never worked on a G-90 but I'm sure with Curt on the other end of a phone we could diagnose it in short order. |
If all this happens let me know. You'll need savvy manual labor there, lefty.
_________________
"Those countries which lag behind in industry, in the application of mechanics and technical chemistry, in the careful selection and utilization of natural products, where the respect for such activities does not permeate all classes of society, will unfailingly decline in prosperity. They will sink faster when neighbor states, with an energetic exchange between science and industry, go forward with renewed vitality."
-- Baron Alexander von Humboldt: 1769-1859
|
|
| Back to top |
|
|
grogthegreat
Joined: 16 May 2007
Posts: 166
Location: San Diego, CA
|
| Posted: Mon Jun 02, 2008 6:26 pm Post subject: |
|
|
I'd be willing to help if you need me. I know how to use and own a multimeter but I don't have any experience with G90s. Just my sony 1252 and NEC 9PG+. I don't know what I could do that stefuel couldn't but I'm only 30 minutes away and don't have much going on right now.
If you would like my help, let me know.
-Greg D.
_________________
First projector: Sony 1252q with 3500 hours
Second projector: NEC 9PG+
current projector: Sony G90
100" 3:4 draper screen.
I must keep upgrading till the voices stop!!
"I CAN HAZ CRT PRUJEKTER."
-Curt Palme
|
|
| Back to top |
|
|
|
|
