| Author |
Message |
studio
Joined: 24 Mar 2006
Posts: 191
|
| Posted: Mon Aug 10, 2009 1:39 pm Post subject: Barco 1209s setup |
|
|
I just finished converting my vertical 1209s to a horizontal machine. I had to cut one end of the bellows lose and rotate it 90° to do so. I was very nervous about doing so, but did so put back together and no leaks. The problem I'm having is I can't get to source 1 or 2. In the manual you go to the random setup and look for svideo option, but can't find it. I have hit the 1 key and the 2 key but nothing. I know this is a simple issue, so go easy on me.
Thanks
Steve
|
|
| Back to top |
|
 |
jkruger
Joined: 24 Oct 2007
Posts: 2435
Location: Carlsbad, CA
|
| Posted: Mon Aug 10, 2009 1:44 pm Post subject: |
|
|
|
My 1209s has no source 1 or 2. The buttons are there but it does not accept those signals.
|
|
| Back to top |
|
|
studio
Joined: 24 Mar 2006
Posts: 191
|
| Posted: Mon Aug 10, 2009 2:21 pm Post subject: |
|
|
|
Yes this is correct. When I bought it 3 or 4 years ago, I'm pretty sure that it played through these ports.
|
|
| Back to top |
|
|
Ile
Joined: 09 Mar 2006
Posts: 1491
Location: Jyväskylä, Finland
|
| Posted: Mon Aug 10, 2009 2:27 pm Post subject: |
|
|
Simulation models and Rungos probably don't have decoder board for video and s-video installed, because those aren't needed and cost something. I have stripped it from my Barco to make cooling better and it also save few mA. 
Check if there is decoder daughter board installed behind switching board.
|
|
| Back to top |
|
|
ecrabb
Forum Moderator
Joined: 13 Mar 2006
Posts: 15909
Location: Utah
TV/Projector: JVC RS40, Epson 5010
|
| Posted: Mon Aug 10, 2009 2:39 pm Post subject: |
|
|
Umm... The question that comes to my mind is, why would you want to use s-video or composite, anyway?
SC
|
|
| Back to top |
|
|
jkruger
Joined: 24 Oct 2007
Posts: 2435
Location: Carlsbad, CA
|
| Posted: Mon Aug 10, 2009 8:53 pm Post subject: |
|
|
|
For the Laserdiscs!
|
|
| Back to top |
|
|
studio
Joined: 24 Mar 2006
Posts: 191
|
| Posted: Mon Aug 10, 2009 10:24 pm Post subject: |
|
|
|
After checking I have realized it does not have the quad board.
|
|
| Back to top |
|
|
Person99
Joined: 09 Mar 2006
Posts: 4899
Location: Flower Mound, TX
|
| Posted: Mon Aug 10, 2009 10:42 pm Post subject: |
|
|
As far as the manual, don't worry about that part. Input a source of the resolution you intent to use on the port you intend to use, then just do set up from the genlocked pattern. Even better is to do set up from a source generated pattern if possible (for instance, HDNet broadcasts patterns for cable/sat source set up, and their are HD calibration discs).
_________________
Dave
A train station is where the train stops. A bus station is where the bus stops. On my desk, I have a work station....
|
|
| Back to top |
|
|
studio
Joined: 24 Mar 2006
Posts: 191
|
| Posted: Tue Aug 11, 2009 12:27 am Post subject: |
|
|
|
If using a computer with a daul head card what kind of settings would I use? It's not a high end card. I'm just doing some initial test.
|
|
| Back to top |
|
|
|
|
